NSK axis and axis cooperation detection

Home>Bearing knowledge>Detection of cooperation between NSK shaft and shaft
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

NSK axis and axis cooperation detection

Source: China Bearing Network Time: 2014-08-22
/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
In the process of ordinary use of NSK bearings; the cooperation gap between the bearing and the shaft must be suitable. So how to test it is appropriate?
Radial clearance can be detected by the following methods.
1. The ruler detection method is about the bearing with larger diameter; the gap is larger; it is directly detected with a narrow feeler gauge. For the bearing with smaller diameter; the gap is smaller than that of the 槐阌 卟饬浚 卟饬浚 岢 岢 牟嘞叮槐匦胗 穸 穸 钡 钡 钡 钡 钡 钡.
2, the lead detection method using the lead method to detect the bearing gap is more accurate with the feeler gauge; but more troublesome. The aluminum wire used for testing should be soft; the diameter should not be too big or too. Noisy this paragraph 湎 pocket 1. 5 ~2 times; in practice, soft lead wire is usually used for testing.
When testing; first open the bearing cover; use the appropriate diameter of the lead wire; cut it into 15~40 mm long section; place it on the journal and the upper and lower bearing interface; cover the bearing cover; tighten according to the regular torque Bolt; then loosen the bolt; remove the bearing cap; use a micrometer to detect the thickness of the flattened wire; find the average value of the bearing top clearance.
If the headspace is too. Slightly thin (11) 峦呓岷 嫔 嫔 . .. If too large; then reduce the pad, scrape the ground or cast the tile from the head.
Adjustment of bearing bushing force: In order to avoid the possible transition and axial movement of the bearing bush during operation; in addition to cooperating with interference and stop parts; the bearing bush must also be pressed with the bearing cap; the measuring method is the same as the measuring head gap method ; measure the thickness of the soft lead wire; can calculate the bearing bushing force (indicated by the amount of elastic deformation after the bushing is tightened)
Usually, the bearing force of the bearing bush is between 0. 02 and 0. 04 mm. If the pressing force does not meet the specifications, it can be adjusted by increasing or decreasing the thickness of the gasket at the joint surface of the bearing and the bearing seat; the back of the tile is not allowed to be padded.
In addition to ensuring radial clearance, the plain bearings should also ensure axial clearance. When detecting axial clearances; move the shaft to a pole orientation; then measure the axis from one pole to the other with a feeler gauge or dial indicator The amount of turbulence is the axial gap.
When the clearance of the sliding bearing does not conform to the rules; adjustment should be made. The split bearing is often used to adjust the radial clearance (top clearance).
I know enough to grasp the detection method; I trust that we are using NSK bearings; we will take a lot of detours.
Recommend to friends comments close window

Bearing related knowledge
Selecting the sounder to distinguish the FAG bearing in the good and bad work of the bearing: pay attention to the bearing smooth grease that can be used to the extreme low temperature
Analysis of the Influence of TIMKEN Bearing Material on Its Life Cycle
NSK bearing device and disassembly


This article links to http://
Please indicate the bearing network http://

Previous:The timing view of FAG bearings is especially important. Next:Inch tapered roller bearings LM102949/10

LED Sensor Batten Lights

LED Sensor Batten Lights has options of microwave sensor and infrared sensor. There are two sensing modes. One is 0-10v dimming, and the other is on/off.

The main difference between these two modes is that the 0-10v dimming mode can set the brightness of the light after the person walks, and the pending time of this brightness can also be set. On/off mode, you can only set the time for the lights to turn off after a person walks, but not the brightness (that is, functions 3, 4 cannot be implemented). The 0-10v dimming mode is more intelligent.

Briefly introduce the function of sensor light:

1. Set up daylight threshold: If the ambient light is higher than the set brightness, the sensing function will not be triggered.

2. Set up the hold time: The time for the light to maintain brightness after the person walks away.

3. Set up a stand-by dim level: set the brightness maintained after the person walks

4. Set up stand-by time: After the person walks, the time to maintain low brightness

5. Set up detection area: Set the detection area.

Toggle button can set the remote distance of remote control and sensor.


If you need sensor lights in factories or warehouses, corridors, or other indoors, you can choose this LED Sensor batten lights. If you need IP66 sensor light, you can choose Sensor Waterproof Light.

Motion Sensor Led Light,Sensor Led Light,Motion Sensor with Led Light,Led Light Motion Sensor

SHENZHEN LITEHOME OPTOELECTRONIC TECHNOLOGY CO., LTD. , https://www.litehomelights.com

Posted on