CNC lathe processing beveling machine product maintenance warranty
1. Daily inspection of CNC lathe for processing steel beveling machine <br style="font-family:;"> The main components of CNC lathe beveling machine processing equipment include: main shaft, hydraulic system lubrication system, cooling system, guide rail Lubrication system, pneumatic system. The daily inspection of the CNC lathe plate beveling machine equipment is based on the normal conditions of each system. For example, when performing the process detection of the lathe spindle lubrication system of the beveling machine, the power lamp should be on, the hydraulic pump should be in normal operation, and if the power lamp is not lit, the spindle should be stopped and contact the mechanical engineer. Carry out repairs.
2. Weekly inspection of CNC lathe beveling machine processing equipment<br style="font-family:;"> Weekly inspection of CNC lathe beveling machine processing equipment The main items include machine tool parts and spindle lubrication system, which should be weekly. Properly check it, especially for machine parts to remove iron filings and perform external debris cleaning.
3. Monthly inspection of CNC lathe plate beveling machine equipment <br style="font-family:;"> Mainly check the power supply and air dryer. The power supply voltage is rated at 180V-220V under normal conditions, and the frequency is 50Hz. If there is any abnormality, it should be measured and adjusted. The air dryer should be removed once a month, then cleaned and assembled.
4. Quarterly inspection of CNC lathe plate beveling machine equipment
It should be checked mainly from three aspects: machine bed, hydraulic system and spindle lubrication system. For example, when inspecting the machine bed, it is mainly to see whether the machine tool accuracy and machine tool level meet the requirements in the manual. If there is any problem, you should contact the mechanical engineer immediately. When inspecting the hydraulic system and the spindle lubrication system, if there is any problem, replace the new oil 6oL and 20L separately and clean it.
5. Half-year inspection of CNC lathe beveling machine equipment <br style="font-family:;"> After half a year, the hydraulic system, the main shaft lubrication system and the X-axis of the CNC lathe beveling machine should be inspected. In case of illness, new oil should be replaced and then cleaned.
After thoroughly familiarizing with and mastering the knowledge of preventive maintenance, you must have a deeper understanding and necessary grasp of the causes and treatment of abnormal phenomena in the hydraulic system. For example, when the oil pump does not spray oil, the pressure is abnormal, there is noise, etc., you should know what are the main reasons and what is the corresponding solution. The reasons and treatment of the abnormal phenomenon of the hydraulic system of the CNC lathe beveling machine should be understood from three aspects:
(1) The main reason for the oil pump of the CNC lathe plate beveling machine is that the liquid level in the fuel tank is low, the oil pump is reversed, the rotation speed is too low, the oil viscosity is too high, the oil temperature is low, the filter is clogged, and the suction pipe capacity is If it is too large, the air is sucked at the oil inlet, the shaft and the rotor are damaged, etc. There are corresponding solutions to the main reasons, such as filling the oil, confirming the sign, and changing when the oil pump reverses.
(2) The pressure of the equipment of the CNC beveling machine is abnormal. The pressure is too high or too low. The main reasons are also various, such as improper pressure setting, poor operation of the pressure regulating valve coil, abnormal pressure gauge, and leakage of the hydraulic system. The corresponding solution is to open and clean according to the specified pressure setting, change to a normal pressure gauge, and check according to each system.
(3) The noisy noise of the CNC lathe plate beveling machine is mainly generated by the oil pump and the valve. When the valve is noisy, the reason is that the flow rate exceeds the rated standard, and the flow should be properly adjusted; when the oil pump has noise, the reason and the corresponding solution are also various, such as high viscosity of oil and low oil temperature, solution To raise the oil temperature; when there are air bubbles in the oil, the air in the system should be released.
All in all, it is necessary to do a good job of preventive maintenance and maintenance of CNC lathe beveling machine equipment.
Author: GIRET Jierui Te automatic plate beveling machine from: http: //
Our company specializes in production: steel beveling machine, automatic steel beveling machine, automatic walking beveling machine, flat beveling machine, automatic single beveling machine, chamfering machine, chamfering machine, small beveling machine, electric beveling Machine, domestic beveling machine, milling machine, desktop milling machine, portable beveling machine, hand-held beveling machine, steel plate/arc dual-purpose beveling machine, steel plate/pipe dual-purpose beveling machine, portable beveling machine , portable milling machine, open processing machine, automatic edge planing machine, edge planing machine
A ballcock (also balltap or float valve) is a mechanism or machine for filling water tanks, such as those found in flush toilets, while avoiding overflow and (in the event of low water pressure) backflow. The modern ballcock was invented by José Antonio de Alzate y RamÃrez, a Mexican priest and scientist, who described the device in 1790 in the Gaceta de Literatura Méxicana.[1] It consists of a valve connected to a hollow sealed float by means of a lever, mounted near the top of the tank. The float is often ball-shaped, hence the name ballcock. The valve is connected to the incoming water supply, and is opened and closed by the lever which has the float mounted on the end. When the water level rises, the float rises with it; once it rises to a pre-set level, the mechanism forces the lever to close the valve and shut off the water flow. This is an example of negative feedback and of proportional control.
Ball Cock, Brass Ball Bibcock, Ballcock Valve, Toilet Ballcock Valve
ZHEJIANG KINGSIR VALVE CO., LTD. , https://www.kingsir-valves.com