The decoration knowledge about the installation of bathroom plumbing is a problem that many owners care about. The water pipe in the bathroom is a very important part of the bathroom. It can be said that the water pipe is the soul element of the bathroom. Without the water pipe, the bathroom will not function properly. The toilet pipe is divided into a water pipe and a sewage pipe. For these two different water pipes, the installation method is not the same. Today we will introduce how to install the bathroom water pipes.
When installing the bathroom plumbing, first consider the bathroom layout, combined with the location of the water (because the location of the water is generally not moving, if moving is very troublesome, you need to raise the ground no less than 10 cm (cm) in the water plus bends to change the waterway, generally affect the flush The effect, so it is not recommended to change the water), according to the facilities for the toilet, arrange the location of the water pipe. Then slotted in the wall, put the upper pipe buried in the wall plastering, outside the tile. Hot and cold water holes in the wash basin at a distance of ten centimeters, left hot right cold; hot and cold water holes in the shower is generally fifteen centimeters, left hot right cold. Toilets, mop pools, washing machines, etc. do not need hot water holes.
Decoration knowledge of hot and cold water pipe installation
1 The hot and cold water pipes of the bathroom should not be too close to each other. Shower hose height is between 1.8M--2.1M.
2 The installation of the bathroom water pipe, the general water pipe does not go to the top, the cold and hot water outlet must be horizontal, generally left right hot right, the pipe laying needs to be flat and straight, the layout should be safe and reasonable. The location of pipe clamps and the slope of the pipeline should all meet the requirements of the code. All types of valve installation should be correct and level, easy to use and repair.
3 The cold and hot water pipes are all in the wall. The depth of the tank needs to be checked when grooving. The hot and cold water pipes cannot be the same as the tank.
4 When installing the inlet and outlet of the water heater, the inlet valve and inlet valve must be considered and installed in the corresponding position.
Decoration knowledge of plumbing installation considerations
1 The inlet valve should be equipped with an indoor main valve. Before installing, check whether the water pipe and connection accessories are damaged, trachoma or crack.
2 When installing kitchen and sanitary pipes, the size of the pipe on the wall should take into account the final size of the wall tiles after they are attached, ie, the thickness of the wall tiles is taken into consideration in advance.
3 In the wall and under the ground, use as few or no connection fittings as possible to reduce the potential for leakage. The connection fittings must be installed securely and without leakage.
4 When designing the water pipe, the installation position of the faucet and the arrangement of the water should be taken into account. At the same time pay attention to the location of the power outlet is appropriate. Put the drum washing machine in the kitchen cabinet to determine the size of the washing machine and the kitchen cabinet, so as to keep the position of the water.
5 Pipeline pressure experiment should be done after the completion of waterway reform. The experimental pressure should not be less than 0.6MPa. The time is 20-30 minutes.
6 The right and left position of the shower mixing valve is correct, and it is installed in the middle of the bathtub (the bath size is determined first), the height is 150-200mm in the bathtub, and the outlet of the jacuzzi is reserved according to the model. The water mixing valve hole spacing is generally maintained at (concealed) 150mm, (surface mounted) 100mm, link shower based on the height of the room and the owner's individual needs to determine the location of the outlet.
7 Place the water inlet of the toilet as far as possible where it can be blocked by the toilet. One-piece toilets should be based on the model to determine the location of the outlet, generally left in the center of the toilet outlet 200 mm left.
8 The height of the water supply outlet (elbow) on the wall should be appropriate. It is necessary to facilitate maintenance and to expose the hose as little as possible, without additional hoses, giving a simple, beautiful visual. For the pedestal basin with no cupboard below, the height of the mouth is reserved, and it should generally be set at about 500-600mm on the ground. The sluice basin outlet should be set in the center of the bottom of the column or behind the column, as far as possible with the column to block. Wall-mounted washbasins (without columns, no cabinets) must be provided with drainage pipes (that is, drain pipes into the wall) in a horizontal manner from the elbows at the wall.
Edit summary:
The installation of bathroom plumbing should comply with the principle of convenience and practicality, at the same time it should not look messy and affect the overall decorative effect of the bathroom. The quality and scientificity of the installation of bathroom plumbing must be high. The toilet cannot be drained for three days. It will cause the greatest problems in people's lives. The installation of a good toilet pipe is certain for the use of toilets and the elimination of odors. Help. About the decoration of the bathroom plumbing installation is introduced here, and I hope to help everyone.
Bathroom Decoration Construction Knowledge Entrance Decorating Toilet Interior Decoration Decoration Socket Flooring Tile Cabinet Door Kitchen Wall Tile Cabinet Kitchen Cabinet Door Bathroom Tile Bathroom Door Bathroom Wall Tile Bathroom Size Bathroom Wash Basin Integral Toilet Bathroom Design Toilet Door Size Floor Tile Ceramic Tile
Ethylene propylene rubber O-ring is formed by copolymerization of ethylene and propylene. The main chain is not double chain, so the heat resistance, aging resistance, ozone resistance and stability are excellent, but sulfur can not be added. Because sulfur cannot be added, it is generally not used for food or exposed to aromatic hydrogen. It is basically used as a seal in the brake and radiator of the automobile water tank.
ZXS SEALING PRODUCTS FACTORY , https://www.zxs-seal.com