Wood lacquer deployment
Wood lacquers are highly flammable liquids that may cause discomfort when inhaled or in contact with the skin, so the product is intended for use only by professionals. The most common polyester paint on the market consists of a master paint, a hardener and a thinner. Before the construction, professionals need to deploy the product according to the specific requirements of the product description.
Wood Coatings Construction Environment
Wood paint construction requires proper conditions and conditions, such as temperature, humidity, light, ventilation, and hygiene to achieve good results.
Wood paint construction is best carried out at room temperature (15-30 °C) conditions, the temperature is too low, paint film becomes slower; temperature is too high (more than 35 °C), brushing performance will be adversely affected.
Avoiding damp air is not good for most paints, especially lacquer, polyurethane paint, etc. Construction in wet and rainy weather can cause whitening or slow drying.
Adequate light helps to see the paint, identify whether the coating is uniform, and avoid brushing or sagging in time, so it should be selected in a well-lit room for construction.
The construction site should have ventilation equipment to maintain a proper amount of fresh air circulation. This will not only be beneficial to the health of the constructors, but also be conducive to film formation and reduce the risk of fire. However, the speed of air circulation must not be too fast so as not to affect the quality of the coating.
The construction environment must be kept clean. The dust and debris generated during the construction process should be immediately removed. Otherwise, the final effect of the paint film will be affected. The clean construction environment is especially important when applying floor paint.
Wood paint construction sequence
White blank sheet → Polished → Substrate closed (scrape putty) → Polished → Brushed primer (first pass) → Polished → Brushed primer (second to third pass) → Full polish → Brush finish (first All over) → polish → brush finish (second pass).
Renovation Considerations Three Trees Paint Nature Floor Paint Coating Room
About high speed Door Accessories:
1.Driving system: High Speed Door Servo System motor and control, motor SNMA / SEJ +reducer+flang+encoder+control box
2.Other accessories: Middle aluminium bar, bottom aluminium bar, aluminium vertical track, stainless steel vertical track, brushes,round nylon strip, PVC roll, rolling steel tube complete, drum be;;s for rolling tube, side end covers, stainless steel cover, steel tubes, air bag sensor system, safety light beam, Microwave sensor 24 Gigahertz,PVC welding machine, smoke and fire sensors, PVC transparent window, magnetic loop, photocell, remote control, manual push button, sound warning alarm Led lamp traffic light
For some main accessories, here is detain introduction:
1).24G radar sensor:
Brand: Hofic
Technology: Microwave processor
Maintain time: 0.5s
Protection: IP54
Transmitting frequency: 24.125GHz
Maximum installation height: <5meter
Transmitting power density: <5mw/cm2
Power consumption: <1W(VA)
Installation angle: 0-90°(lengthways) -30-30°(crosswise)
Supply voltage: AC&DC 12V-30V
2).Photocell:
Approval CE & ISO9001
Power supply AC/DC 12-30V
Static current 25A
Action current 40mA
Mounting distance Max 10m
NO or NC contact Done by NO./NC. contact selection
Working environment temperature -42℃ to +45℃
Working environment humidity 10 to 90%RH
Appearance dimensions( controller) 123*50*32mm(L*W*H)
Appearance dimensions(Magic eye head) 19*13mm(L*D)
3). Remote control
Operating Voltage: AC220V/50HZ+-20%
Transmit power:≤100mW;Super regenerative module, strong anti-interference
Operating temperature:-30℃-+70℃
Working frequency: 433MHZ;transmitter 1527, millions of encoding chip
Accept sensitivity:≤110dB
Manipulation method: electric remote control
Configure the quantity: Wireless number; factory configuration transmitter two. Can be equipped with PT2272 digital decoder chip
Configure the function: Up, down, stop, anti-lock full-featured reproduction
4). Magnetic loop
Voltage: 12V AC/DC +-10% 24V 115V AC+-10% 230V
Power: <2VA
Continued electrical output: 7A / 250V AC
Frequency range: 20 to 200K Hz
Response time: infinity (factory setting) or adjust maintain time
Sensitivity: 0.01% to 0.1% divided into 3 levels
Protection level: IP30
Electromagnetic compatibility (EMC) Complies with EM50081-1 and EN50082-2
Detection loop inductance: the limit of 40uH to 100uH ideal value 80uH to 300uH
Operating temperature: -25 ℃ to 70 ℃
Storage temperature: -40 ℃ to 85 ℃
Relative humidity: <90% non-condensing
Temperature compensation: automatic compensation up to 50 ℃ / h
Connection type: 11 pin DIN rail socket
Dimensions: 41 * 78 * 85 mm (width * height * length)
Weight: 250 grams
5). manual push button
This exit switch button is made of ABS and has built-in indicator light make it looks more elegant and fashionbale. It can be widely used in public entrance gates, public door, home, office, hotel, etc.
Door Exit Button Push To Exit Switch Door Opener For Access Control Security
Main Feature
Fashionable appearance
Made of ABS Plastic
Easy to install and operate
Used for access control
Specification
Mechanical Life: 500,000 test
Material: Plastic
6). Limit switch encoder
Voltage: DC5V-24V
Output voltage: high voltage≥85%Vcc, low voltage≤0.5V
Maximum mechanical speed:6000rpm
Anti-vibration: 50m/s,10-200HZ,XYZeach way 2 times.
Current consumption:≤30mA
Response frequency: 0-100KHZ
Protection: waterproof,oil proof,dust prevention, IP54
The output code system: binary code
Operating life: MTBF≥30000(+25℃,2000rpm)
Rotational inertia:4.0x10-8kgm²
Maximum load:radial direction20N
Axial direction:10N
Weight: about 0.4kg
High Speed Door Accessories,High Speed Door,Electronic High Speed Door Accessories
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hffastdoor.com